Home / excel rental property analysis / Energy Efficiency Assessment Report Format

Energy Efficiency Assessment Report Format - excel rental property analysis







Company Log
Name of Facility
Address of facility




Data Center Energy Efficiency Assessment









Assessor and affiliation










Disclaimer


This report was prepared by Qualified Assessor in the course of performing an energy assessment contracted for and sponsored by Sponsor. Reproduction or distribution of the whole, or any part, of the contents of this document without written permission of Sponsor is prohibited. Neither the assessor, Sponsor nor any of its employees make any warranty or representations, expressed or implied, or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any data, information, method product or process disclosed in this document, or represents that its use will not infringe any privately-owned rights, including, but not limited to, patents, trademarks, or copyrights.



This report uses preliminary information from vendor data and technical references. The report, by itself, is not intended as a basis for the engineering required to adopt any of the recommendations. Its intent is to inform the site of potential energy saving opportunities and very rough cost savings. The purpose of the recommendations and calculations is to determine whether measures warrant further investigation.




Acknowledgments



Authors


Joe Green Engineer - qualified assessor


The Authors Would Like to Acknowledge the Contributions and
Assistance of the Following People:

Site staff or others who helped





TABLE OF CONTENTS





1. Facility Overview 4


2. Facility Energy Use 4

IT Equipment Loads 4
Data Center Energy End Use 5

3. Mechanical System Description 5


4. Electrical System Description 6


5. Benchmarking 6

Data Center Infrastructure Efficiency (DCiE) 6

6. OBSERVATIONS 6


7. rECOMMENDED ENERGY EFFICIENCY MEASURES 6

IT equipment 6
HVAC 7

AppendiCES 8



Executive Summary

Summarize the following: sponsor, site, contractor, brief description of site, use of DC Pro tools, etc.

A number of energy efficiency opportunities with varying payback periods were identified during the assessment. Based on an estimated energy cost of $xxxx/kWh, energy cost savings of approximately $xx,xxx/yr are possible through measures that have an average payback period of x.x years and represent approximately x% energy savings. The table below summarizes the projected economics for the recommended measures:

|Grouped Efficiency |Estimated Installed Cost |Estimated Yearly Energy Savings |Estimated Simple Payback - Years |
|Measures | | | |
| | | | |
| | | | |
|Totals |$ |$ |weighted ave. |

Table 1 - Summary of Estimated Savings and Payback Times

Additional high level findings



Facility Overview

High level description of facility

Facility Energy Use

The total electrical demand was on average approximately XXX kW with a yearly energy use of approximately X.X GWh/yr. Approximately XX% of the energy use is related to the servers. The data center is [stand alone; located in an office building; etc.], it was [not] separately submetered, and the team had to develop the energy usage through a combination of temporary submetering, spot measurements and/or spreadsheet calculations.


IT Equipment Loads

Summarized in Table 2 below is the average power (kW) for IT equipment

|Data Center Areas |Area (sf) |IT equipment load (kW) |Power Density (W/sf) |
| | | | |
| | | | |
|Totals | | | |


Table 2 IT equipment load




Data Center Energy End Use

The electrical end use breakdown associated with the data center space was determined and is shown in Table 3.



|Data Center End Use |Approximate Area |Average IT |Power Density |
| |(SF) |Load (kW) |(W/SF) |
|XXX |x,xxx |xxx |xx |
|XXX |x,xxx |xx |xx |
|TOTALS: |x,xxx |xxx |xx |

Table 3 - Summary of Data Center Electrical End Use



[pic]
Example Figure 2 –Electrical Breakout by End Use

Replace with actual breakdown


Mechanical System Description


Figure 3 – HVAC System Schematic


Electrical System Description

UPS System:

Example Table 4. UPS Electrical Measurements

| |Units |UPS-A |UPS-B |Combined |
|UPS Input |kW |xxx |xxx |xxx |
|UPS Output |kW |xxx |xxx |xxx |
|Losses |kW |xx |xx |xx |
|Efficiency |% |xx |xx |xx |
|Load Factor |% |xx |xx |xx |



Distribution transformers/PDUs:

Lighting:

Benchmarking

The purpose of this section is to summarize the metrics that were gathered as part of the assessment process and compare them to data from other facilities, where available.


5.1 Overall energy Efficiency metrics

The table below indicates the metrics that were collected and the interpretation of their values.

|Metric ID |Metric Name |Unit |Value |Interpretation |
|EM.M.1 |DCiE (site energy) |- | | |
| |(IT energy use / total energy use) | | | |
|EM.M.2 |PUE |- | | |
| |(Total Power/IT Power) | | | |
|EM.M.3 |HVAC Effectiveness |- | | |
| |(IT Power /HVAC Power) | | | |
|EM.M.4 |Site Energy Use Intensity |Site BTU/sf-yr | | |
|EM.M.5 |Source Energy Use Intensity |Source BTU/sf-yr | | |
|EM.M.6 |Purchased Energy Cost Intensity |Energy $/sf-yr | | |
|EM.M.7 |Peak Electrical Demand Intensity |Peak W/sf | | |


Charts for selected metrics are provided below

[pic]
Figure 4 - Data Center Infrastructure Efficiency (DCiE)

[pic]

Figure 4 - Data Center Power Utilization Effectiveness (PUE)






[pic]

Figure 6 - IT equipment power/HVAC power





5.2 Air Management and Air Distribution Metrics

Several server intake and exhaust temperatures were collected from a representative sample of servers in the data center. In addition, measurements of return and supply air temperatures were taken from all of the CRAC or CRAH units as well as from the perforated tiles. The goal is to establish an understanding of the air management performance, identify any issues such as potential hot spots. From these temperature measurements, the following indices were calculated:

Rack Cooling Index (RCI):
RCI is a dimensionless measure of how effectively the equipment is cooled within a given intake temperature specification (e.g., ASHRAE, NEBS). It provides a measure of the conditions at the high (HI) end and at the low (LO) end of the specified temperature range. RCIHI=100% means that no intake temperature is above the maximum recommended, and RCILO=100% means that no intake temperature is below the minimum recommended. Using ASHRAE Class 1 temperature specification, “poor” conditions are ≤90% whereas “good” conditions are ≥96%. The RCI is assuming the ASHRAE Class 1 recommended intake temperature

Return Temperature Index (RTI):
The Return Temperature Index (RTI) is a dimensionless measure of the actual utilization of the available temperature differential in the equipment room as well as a measure of the level of by-pass air or recirculation air in the data center. 100% is generally the target; >100% ( recirculation air;

What is REV in real estate?